Аз eBayUnbrandedҲолат: New
Dryer Cord Strain Relief Clamp for Flat 3-Wire 3-Conductor Cords
Пеш аз пардохт мувофиқатро санҷед
- Ҳолат
- New
- Brand
- Unbranded
Модел, бренди мувофиқ ва MPN-ро бо дастгоҳи худ муқоиса кунед: қисмҳо баргардонида намешаванд.
- Нархи мол дар мағоза
- $8.09
- Андози фурӯш (ИМА)
- $0.83
- Ҳаққи хизмати Sanduq
- $5.00
- Интиқол ба Тоҷикистон (~0,5 кг)
- $8.00
- Расонидан дар Тоҷикистон
- $2.00
- Табдили асъор
- $0.96
Интиқол аз рӯи вазни мол ҳисоб шудааст; пеш аз парвоз қуттӣ баркашида мешавад, фарқ пардохт ё баргардонида мешавад.
Бозгашт нест
Мо аз номи шумо мехарем, бинобар ин молро баргардонидан ё иваз кардан мумкин нест. Андоза, ранг ва моделро пеш аз пардохт санҷед.
Фурӯшанда: huntleycd1 · 100.0% positive (952)
Асл бо забони англисӣ
Хусусиятҳо
- Color
- Steel
- Country of Origin
- China
Тавсиф
For sale is a single dryer strain relief cord clamp (cord not included). The clamp is used to keep the cords' connections from pulling out of the dryer and causing a potential electrical fault and/or fire. The clamp anchors the cable to the frame of the dryer. A single clamp assembly consists of four parts, the top half of clamp, the bottom half of clamp, and two screws used to secure the top and bottom halves together. This clamp is for flat 3-conductor cords. This listing is for quantity one (1) clamp assembly. Cord is not included. The flat, 3-conductor (10 AWG) cord shown in the photographs for reference is 0.78 inches (19.89 mm) in width, and 0.31 inches (7.93 mm) thick. As shown in the pictures, the ear widths are 0.94 inches (23.97 mm). The maximum clamp opening size is 0.68 inches (17.36 mm), and the maximum ear size is 2.48 inches (63.09 mm). The minimum clamp opening size is 0.23 inches (5.91 mm), and the minimum ear size is 2.02 inches (51.31 mm). The Whirlpool dryer cord opening measured 1.16 inches (29.5 mm) and this clamp worked fine as shown in the pics. Finally, as also shown in the photographs, the clamp secures tight to the cord with roughly 1/8 inch of space left between the clamp halves. Check out my other listing for round dryer cable clamps. Installation instructions are: 1. With no screws installed, insert top and bottom halves of clamp into dryer opening with the flat "ears" or anchors on the interior and the clamp-to-cable grips on the exterior. 2. Insert cord through the top and bottom halves of clamp while holding clamps in place. 3. Install screws starting through the clamp half with the larger openings (no threads) and then into the half with threads. It may be necessary to squeeze both halves together with pliers or channel locks as shown in pics to align the clamp holes and so the clamp grips are parallel to each other. 4. Tighten screws until clamp is snug on cord and cord cannot be accidentally pulled out of dryer frame. Note: as shown in pics, with the dryer used to demonstrate this clamp, there was a screw directly under the clamp that was used to secure the dryer back panel onto the dryer frame. This screw prevented the bottom half of the clamp from extending down to the bottom of the cord hole. So it may be necessary to turn the clamp/cord at a slight angle as a work around to this screw interfering with the ear of the clamp bottom half.
- • For sale is a single dryer strain relief cord clamp (cord not included). The clamp is used to keep the cords' connections from pulling out of the dryer and causing a potential electrical fault and/or fire.







